From a3a3e37495447af1bfafbf29b36e894bab90661b Mon Sep 17 00:00:00 2001 From: Harvie Date: Sun, 14 Nov 2010 11:39:17 +0100 Subject: [PATCH] Moved whole Arduino sketchbook to GIT (nothing interesting :-) --- arduino/.gitignore | 4 + .../AM_Broadcast_Modulator.pde | 176 ++++++++++ arduino/Blink/Blink.pde | 40 +++ arduino/{ => BrainFuck}/BrainFuck.pde | 0 .../{DrumMachine.pde => Demo01/Demo01.pde} | 0 arduino/DrumMachine/DrumMachine.pde | 118 +++++++ arduino/FM_Jammer/FM_Jammer.pde | 25 ++ arduino/{ => IR_Jammer}/IR_Jammer.pde | 5 +- arduino/LED_Detector/LED_Detector.pde | 73 +++++ arduino/PiezoBlink/PiezoBlink.pde | 14 + arduino/Pong/Pong.pde | 30 ++ arduino/{ => Sound}/Sound.pde | 0 arduino/SoundMix/SoundMix.pde | 36 ++ arduino/TV_B_Gone/TV_B_Gone.pde | 37 +++ arduino/dtfm/DTFM.pde | 73 +++++ arduino/led_touch/led_touch.pde | 51 +++ arduino/oscilator/oscilator.pde | 36 ++ arduino/serial_midi/serial_midi.pde | 71 ++++ .../tv_b_gone_Pedrocrespo.pde | 309 ++++++++++++++++++ 19 files changed, 1096 insertions(+), 2 deletions(-) create mode 100644 arduino/.gitignore create mode 100644 arduino/AM_Broadcast_Modulator/AM_Broadcast_Modulator.pde create mode 100644 arduino/Blink/Blink.pde rename arduino/{ => BrainFuck}/BrainFuck.pde (100%) rename arduino/{DrumMachine.pde => Demo01/Demo01.pde} (100%) create mode 100755 arduino/DrumMachine/DrumMachine.pde create mode 100755 arduino/FM_Jammer/FM_Jammer.pde rename arduino/{ => IR_Jammer}/IR_Jammer.pde (94%) mode change 100644 => 100755 create mode 100755 arduino/LED_Detector/LED_Detector.pde create mode 100755 arduino/PiezoBlink/PiezoBlink.pde create mode 100755 arduino/Pong/Pong.pde rename arduino/{ => Sound}/Sound.pde (100%) create mode 100755 arduino/SoundMix/SoundMix.pde create mode 100755 arduino/TV_B_Gone/TV_B_Gone.pde create mode 100755 arduino/dtfm/DTFM.pde create mode 100644 arduino/led_touch/led_touch.pde create mode 100644 arduino/oscilator/oscilator.pde create mode 100644 arduino/serial_midi/serial_midi.pde create mode 100644 arduino/tv_b_gone_Pedrocrespo/tv_b_gone_Pedrocrespo.pde diff --git a/arduino/.gitignore b/arduino/.gitignore new file mode 100644 index 0000000..dc5cbd5 --- /dev/null +++ b/arduino/.gitignore @@ -0,0 +1,4 @@ +*.* +!*.pde +!/.gitignore +applet/ diff --git a/arduino/AM_Broadcast_Modulator/AM_Broadcast_Modulator.pde b/arduino/AM_Broadcast_Modulator/AM_Broadcast_Modulator.pde new file mode 100644 index 0000000..3f56794 --- /dev/null +++ b/arduino/AM_Broadcast_Modulator/AM_Broadcast_Modulator.pde @@ -0,0 +1,176 @@ +/*Copy the code below and up load it to the I/O Board +then put some kind of Antenna into PIN 8...PIN 8!!!! +Then tune to AM 1337kHz. +Optional:LED in pin 13 to see what is broadcasting, +also a protoshield to add multiple antenna's. +Lol that code will do morse code saying "I like ice cream"; +*********THE CODE**************************************************** +*/ +//start of code +//WWW.JONNYBLANCH.WEBS.COM +long millisAtStart = 0; +long millisAtEnd = 0; + +const long period_broadcast = 8; //period of shortest broadcast (256 port changes) + +#define LENGTH_DIT 64 +//number of period_broadcasts in one 'dit', +//all other lengths are scaled from this +//Broadcasts on 1337 kHz + +const int length_dit = LENGTH_DIT; //number of periods for dit +const int pause_dit = LENGTH_DIT; //pause after dit +const int length_dah = 3 * LENGTH_DIT; //number of persots for dah +const int pause_dah = LENGTH_DIT; //pause after dah +const int length_pause = 7 * LENGTH_DIT; //pause between words + +void dit(void); +void dah(void); +void pause(void); +void broadcast(int N_cycles); +void dontbroadcast(int N_cycles); + +// ### INC ### Increment Register (reg = reg + 1) +#define ASM_INC(reg) asm volatile ("inc %0" : "=r" (reg) : "0" (reg)) + +void setup() { + + Serial.begin(9600); + DDRB = 0xFF; //Port B all outputs + //Do one dit to determine approximate frequency + millisAtStart = millis(); + dit(); + millisAtEnd = millis(); + Serial.print(millisAtEnd - millisAtStart); + Serial.print(" "); + Serial.print((length_dit + pause_dit) * period_broadcast * 256 / + (millisAtEnd - millisAtStart) / 2); + Serial.print("kHz "); + Serial.println(); +} + +void loop() { + dit(); + dit(); + delay(500); + dit(); + dah(); + dit(); + dit(); + delay(250); + dit(); + dit(); + delay(250); + dah(); + dit(); + dah(); + delay(250); + dit(); + delay(500); + dit(); + dit(); + delay(250); + dah(); + dit(); + dah(); + dit(); + delay(250); + dit(); + delay(500); + dah(); + dit(); + dah(); + dit(); + delay(250); + dit(); + dah(); + dit(); + delay(250); + dit(); + delay(250); + dit(); + dah(); + delay(250); + dah(); + dah(); + delay(2000); + +} + +void dit(void) { + for (int i = 0; i < length_dit; i++) + { + + broadcast(period_broadcast); + + } + + for (int i = 0; i < pause_dit; i++) + { + + dontbroadcast(period_broadcast); + + } + +} + +void dah(void) { + for (int i = 0; i < length_dah; i++) + { + + broadcast(period_broadcast); + + } + + for (int i = 0; i < pause_dah; i++) + { + + dontbroadcast(period_broadcast); + + } + +} + +void pause(void) { + for (int i = 0; i < length_pause; i++) + { + + dontbroadcast(period_broadcast); + + } + +} + +void broadcast(int N_cycles) { + unsigned int portvalue; + for (int i = 0; i < N_cycles; i++) + { + + portvalue = 0; + + do { + PORTB = portvalue; + ASM_INC(portvalue); + } + while (portvalue < 255); + } +} + +void dontbroadcast(int N_cycles) { + unsigned int portvalue; + PORTB = 0x00; + for (int i = 0; i < N_cycles; i++) + { + + portvalue = 0; + + do { + ASM_INC(portvalue); + //add some assembly No OPerations to keep timing the same + asm volatile ("NOP"); + } + while (portvalue < 255); + } +} + +//end of code diff --git a/arduino/Blink/Blink.pde b/arduino/Blink/Blink.pde new file mode 100644 index 0000000..5d27483 --- /dev/null +++ b/arduino/Blink/Blink.pde @@ -0,0 +1,40 @@ +/* + Blink + + Turns on an LED on for one second, then off for one second, repeatedly. + + The circuit: + * LED connected from digital pin 13 to ground. + + * Note: On most Arduino boards, there is already an LED on the board + connected to pin 13, so you don't need any extra components for this example. + + + Created 1 June 2005 + By David Cuartielles + + http://arduino.cc/en/Tutorial/Blink + + based on an orginal by H. Barragan for the Wiring i/o board + + */ + +int ledPin = 13; // LED connected to digital pin 13 + +// The setup() method runs once, when the sketch starts + +void setup() { + // initialize the digital pin as an output: + pinMode(ledPin, OUTPUT); +} + +// the loop() method runs over and over again, +// as long as the Arduino has power + +void loop() +{ + digitalWrite(ledPin, HIGH); // set the LED on + delay(1000); // wait for a second + digitalWrite(ledPin, LOW); // set the LED off + delay(1000); // wait for a second +} diff --git a/arduino/BrainFuck.pde b/arduino/BrainFuck/BrainFuck.pde similarity index 100% rename from arduino/BrainFuck.pde rename to arduino/BrainFuck/BrainFuck.pde diff --git a/arduino/DrumMachine.pde b/arduino/Demo01/Demo01.pde similarity index 100% rename from arduino/DrumMachine.pde rename to arduino/Demo01/Demo01.pde diff --git a/arduino/DrumMachine/DrumMachine.pde b/arduino/DrumMachine/DrumMachine.pde new file mode 100755 index 0000000..85b384a --- /dev/null +++ b/arduino/DrumMachine/DrumMachine.pde @@ -0,0 +1,118 @@ +/* + * Bit-bang sound + * <~~Harvie 2oo8 + */ + +#define sndout 13 + +void sound(char sndpin, float freq, float duration) { //Play bit-bang sound + if(duration<=0) return; if(freq<=0) { delay(duration); return; } + freq=((1000000/2)/freq); //Convert freq to delay (us) + duration*=1000; //Convert duration to us + pinMode(sndpin, OUTPUT); + for(;duration>0;duration-=2*freq) { + digitalWrite(sndpin, HIGH); delayMicroseconds(freq); + digitalWrite(sndpin, LOW); delayMicroseconds(freq); + } + pinMode(sndpin, INPUT); //Close pin to avoid noise (optional) +} + +float get_tone(char tone, char octave) { //Return tone frequency or 0 + if(octave+tone<=0) return 0; + float freq; + switch (tone) { //THX2MS GW-BASIC Reference 4freqs muhaha ;D + case 'c': case 'C': freq=130.81; break; + case 'd': case 'D': freq=146.83; break; + case 'e': case 'E': freq=164.81; break; + case 'f': case 'F': freq=174.61; break; + case 'g': case 'G': freq=196; break; + case 'a': case 'A': freq=220; break; + case 'b': case 'B': freq=246.94; break; + default: return 0; + } + return (freq*pow(2,octave-1)); +} + +void play_melody(char sndpin, char *melody, char octave, int duration) { + for(char i=0;melody[i]!=0;i++) sound(sndpin, get_tone(melody[i], octave), duration); + return; +} + +void setup() { // run once, when the sketch starts + Serial.begin(115200); +} + +void play_drum(char sndpin, char drum) { + char c; int i; float f; + switch (drum) { + //BassDrums + case 'b': for(f=0;f<30;f+=4) {sound(sndpin, 60, 20); delay(f);} break; + case 'B': for(i=0;i<=150;i+=10) sound(sndpin, i, 10); break; + case 'd': for(i=150;i>=0;i-=10) sound(sndpin, i, 10); break; + case 'D': for(i=100;i>=40;i-=10) sound(sndpin, i, 6); break; + //Snares + case 's': for(f=0;f<1;f+=0.1) sound(sndpin, sin(f)*1000, 5); break; + case 'S': for(f=0;f<1;f+=0.1) sound(sndpin, sin(f)*1000+(rand()/100), 5); break; + case 'z': for(f=0;f<1;f+=0.15) { sound(sndpin, sin(f)*1000+(rand()/1000), 5); delay(f*10); } break; + //Crashes + case 'c': for(f=1.2;f<1.5;f+=0.01) { sound(sndpin, 700+(rand()/500), 2); delay(1/sin(f)); } break; + case 'C': for(f=1;f<1.3;f+=0.01) { sound(sndpin, (70+(rand()/500))*(f/0.1), 2); /*delay(1/sin(f));*/ } break; + //Ambient + case 'r': for(i=0;i<300;i++) sound(sndpin, rand()*100, 5); break; + //Intros + case 'i': for(i=0;i<150;i++) sound(sndpin, i*100, 5); break; + case 'I': for(f=0;f<1;f+=0.01) {sound(sndout, sin(f)*550, 10); sound(sndout, cos(f)*400, 10); } break; + //Outros + case 'o': for(f=1;f>0.3;f-=0.01) { sound(sndpin, sin(f)*1000+(rand()/100), 5); delay(40/f); } break; + default: delay(100); + } +} + +void play_rythm(char sndpin, char *rythm) { + for(char i=0;rythm[i]!=0;i++) play_drum(sndpin, rythm[i]); + return; +} + +void loop() { // run over and over again + //delay(10000); return;//Silence! I'll kill you! + //while(1) sound(sndout, rand()/20, 10); + //int i=0; while(1) sound(sndout, i++, 10); + //float i=0; while(1) sound(sndout, sin(i+=0.01)*600, 10); + //float i=0; while(1) { sound(sndout, sin(i+=0.01)*550, 10); sound(sndout, cos(i)*400, 10); } + //sound(sndout, 440, 30000); + + //play_drum(sndout, 'D'); delay(1000); return; + //play_drum(sndout, Serial.read()); return; + + /* + play_rythm(sndout, "r iI "); + play_melody(sndout, "c c c cc dd d eee ", 1, 100); + play_rythm(sndout, "B D B d s B D s B d c B s D C B d S B D S B b s d So "); + */ + + sound(sndout, analogRead(0), 10); return; + +/* + char rythm[]= +"b " +"D D D d D d " +"D D D d D d " +"i " +"D D D d D d " +"D D D d D d " +"I " +"D s D S D d " +"D D z d D d " +"ddDDb " +"D D D d D s " +"D D D d D s " +"o"; + + play_rythm(sndout, rythm); +*/ + /*int octave, duration; + char melody[]="CCDEECCFFAAGGE-CCDEGGEFEDDCC-CCDEECCFFAAGGE-CCDEGGEFEDDC"; octave=1; duration=300; //Bob Marley's Redemption song - intro ;D + play_melody(sndout, melody, octave, duration);*/ + delay(4000); +} + diff --git a/arduino/FM_Jammer/FM_Jammer.pde b/arduino/FM_Jammer/FM_Jammer.pde new file mode 100755 index 0000000..1883d5a --- /dev/null +++ b/arduino/FM_Jammer/FM_Jammer.pde @@ -0,0 +1,25 @@ +/* + * Blink + * + * The basic Arduino example. Turns on an LED on for one second, + * then off for one second, and so on... We use pin 13 because, + * depending on your Arduino board, it has either a built-in LED + * or a built-in resistor so that you need only an LED. + * + * http://www.arduino.cc/en/Tutorial/Blink + */ + +int Pin = 13; // LED connected to digital pin 13 +int + +void setup() // run once, when the sketch starts +{ + pinMode(Pin, OUTPUT); // sets the digital pin as output +} + +void loop() // run over and over again +{ + delay(1); + digitalWrite(Pin, HIGH); // sets the LED onv + digitalWrite(Pin, LOW); // sets the LED offv +} diff --git a/arduino/IR_Jammer.pde b/arduino/IR_Jammer/IR_Jammer.pde old mode 100644 new mode 100755 similarity index 94% rename from arduino/IR_Jammer.pde rename to arduino/IR_Jammer/IR_Jammer.pde index ad96955..dab2732 --- a/arduino/IR_Jammer.pde +++ b/arduino/IR_Jammer/IR_Jammer.pde @@ -15,7 +15,8 @@ #define ledpin 13 //Maybe you will have to experiment also with this value int bitlen = 5; -int d, i; +int d; +float i; void setup() { pinMode(ledpin, OUTPUT); @@ -25,7 +26,7 @@ void loop() { for(d=1000/100;d<=1000/20;d++) { // 1000/frequency in kHz //You maybe have to experiment with ^^^ this ^^^ values //Frequency sweeping: 100->20 kHz works, i saw 60->1 too - for(i=0;i 100 ohm resistor +// < +// | +// | +// ----- +// / \ LED, maybe a 5mm, clear plastic is good +// ----- +// | +// | +// + digital3 +// +// What we are going to do is apply a positive voltage at digital2 and +// a low voltage at digital3. This is backwards for the LED, current will +// not flow and light will not come out, but we will charge up the +// capacitance of the LED junction and the Arduino pin. +// +// Then we are going to disconnect the output drivers from digital2 and +// count how long it takes the stored charge to bleed off through the +// the LED. The brighter the light, the faster it will bleed away to +// digital3. +// +// Then just to be perverse we will display the brightness back on the +// same LED by turning it on for a millisecond. This happens more often +// with brighter lighting, so the LED is dim in a dim room and brighter +// in a bright room. Quite nice. +// +// (Though a nice idea, this implementation is flawed because the refresh +// rate gets too long in the dark and it flickers disturbingly.) +// +#define LED_N_SIDE 2 +#define LED_P_SIDE 3 + +void setup() +{} + +void loop() +{ + unsigned int j; + + // Apply reverse voltage, charge up the pin and led capacitance + pinMode(LED_N_SIDE,OUTPUT); + pinMode(LED_P_SIDE,OUTPUT); + digitalWrite(LED_N_SIDE,HIGH); + digitalWrite(LED_P_SIDE,LOW); + + // Isolate the pin 2 end of the diode + pinMode(LED_N_SIDE,INPUT); + digitalWrite(LED_N_SIDE,LOW); // turn off internal pull-up resistor + + // Count how long it takes the diode to bleed back down to a logic zero + for ( j = 0; j < 30000; j++) { + if ( digitalRead(LED_N_SIDE)==0) break; + } + // You could use 'j' for something useful, but here we are just using the + // delay of the counting. In the dark it counts higher and takes longer, + // increasing the portion of the loop where the LED is off compared to + // the 1000 microseconds where we turn it on. + + // Turn the light on for 1000 microseconds + digitalWrite(LED_P_SIDE,HIGH); + digitalWrite(LED_N_SIDE,LOW); + pinMode(LED_P_SIDE,OUTPUT); + pinMode(LED_N_SIDE,OUTPUT); + delayMicroseconds(1000); + // we could turn it off, but we know that is about to happen at the loop() start +} diff --git a/arduino/PiezoBlink/PiezoBlink.pde b/arduino/PiezoBlink/PiezoBlink.pde new file mode 100755 index 0000000..1b257c4 --- /dev/null +++ b/arduino/PiezoBlink/PiezoBlink.pde @@ -0,0 +1,14 @@ +// Fading LED +// by BARRAGAN + +int ledpin = 11; // light connected to digital pin 9 + +void setup() +{ + pinMode(ledpin, OUTPUT); +} + +void loop() +{ + analogWrite(ledpin, analogRead(0)); // sets the value (range from 0 to 255) +} diff --git a/arduino/Pong/Pong.pde b/arduino/Pong/Pong.pde new file mode 100755 index 0000000..66f2c8c --- /dev/null +++ b/arduino/Pong/Pong.pde @@ -0,0 +1,30 @@ +/* Pong controller (for use with hPong) + * <~~Harvie 2oo8 + */ + +#define inpin 0 +int min = 65535, max = 0; +int stadium_max = 14; +char offset = 8; +float val = 0, oldval = -255; + +void setup() // run once, when the sketch starts +{ + stadium_max+=offset; + Serial.begin(115200); +} + +void loop() // run over and over again +{ + val = analogRead(inpin); + if(valmax) max=val; + val=(((val-(min))/(max-(min)))*stadium_max)-offset; + if(val!=oldval) { + oldval = val; + //Serial.print(min, DEC); Serial.print("-"); Serial.print(max, DEC); Serial.print("\n"); + //Serial.print(val, DEC); Serial.print("\n"); + Serial.print(val, BYTE); + } + delay(1); +} diff --git a/arduino/Sound.pde b/arduino/Sound/Sound.pde similarity index 100% rename from arduino/Sound.pde rename to arduino/Sound/Sound.pde diff --git a/arduino/SoundMix/SoundMix.pde b/arduino/SoundMix/SoundMix.pde new file mode 100755 index 0000000..6466151 --- /dev/null +++ b/arduino/SoundMix/SoundMix.pde @@ -0,0 +1,36 @@ +/* + * Bit-bang sound + * <~~Harvie 2oo8 + */ + +#define sndout 13 + +char mixer; + +void sound(char sndpin, float freq, float duration) { //Play bit-bang sound + if(duration<=0) return; if(freq<=0) { delay(duration); return; } + freq=((1000000/2)/freq); //Convert freq to delay (us) + duration*=1000; //Convert duration to us + pinMode(sndpin, OUTPUT); + for(;duration>0;duration-=2*freq) { + digitalWrite(sndpin, HIGH); delayMicroseconds(freq); + digitalWrite(sndpin, LOW); delayMicroseconds(freq); + } + pinMode(sndpin, INPUT); //Close pin to avoid noise (optional) +} + +void setup() { // run once, when the sketch starts + pinMode(sndout, OUTPUT); + pinMode(sndout-1, INPUT); +} + +void loop() { // run over and over again + //delay(10000); return;//Silence! I'll kill you! + //float i=0; while(1) { sound(sndout, sin(i+=0.01)*550, 10); sound(sndout, cos(i)*400, 10); } + digitalWrite(sndout, digitalRead(sndout-1)); + /* int octave, duration; + char melody[]="CCDEECCFFAAGGE-CCDEGGEFEDDCC-CCDEECCFFAAGGE-CCDEGGEFEDDC"; octave=1; duration=300; //Bob Marley's Redemption song - intro ;D + play_melody(sndout, melody, octave, duration); */ + //delay(2000); +} + diff --git a/arduino/TV_B_Gone/TV_B_Gone.pde b/arduino/TV_B_Gone/TV_B_Gone.pde new file mode 100755 index 0000000..678353e --- /dev/null +++ b/arduino/TV_B_Gone/TV_B_Gone.pde @@ -0,0 +1,37 @@ +/* + * Arduino TV-B-GONE + * <~~Harvie 2oo8 + * + * THX 2 Ladyada + * http://www.ladyada.net/make/tvbgone/ + * + */ + +//#include "NAcodes.c" +//#include "NAcodes2.c" +#define ledpin 13 +//Maybe you will have to experiment also with this value +int d; +float i; + +void fire_code(int outpin, long freq, fuck *code) { //kHz + freq = 1000000/(freq*1000); //freq2millis + for() +} + +void setup() { + pinMode(ledpin, OUTPUT); +} + +void loop() { + for(d=1000/100;d<=1000/20;d++) { // 1000/frequency in kHz + //You maybe have to experiment with ^^^ this ^^^ values + //Frequency sweeping: 100->20 kHz works, i saw 60->1 too + for(i=0;i 0) pin = true; + if( sin((pos*high)/1000*(2*PI)) > 0) pin = true; + + if(pin) digitalWrite(outpin, HIGH); else digitalWrite(outpin, LOW); + } +} + +int dtfm_key(char outpin, char key) { + switch (key) { + case '1': dtfm_tone(outpin, 697, 1209); break; + case '2': dtfm_tone(outpin, 697, 1336); break; + case '3': dtfm_tone(outpin, 697, 1477); break; + + case '4': dtfm_tone(outpin, 770, 1209); break; + case '5': dtfm_tone(outpin, 770, 1336); break; + case '6': dtfm_tone(outpin, 770, 1477); break; + + case '7': dtfm_tone(outpin, 852, 1209); break; + case '8': dtfm_tone(outpin, 852, 1336); break; + case '9': dtfm_tone(outpin, 852, 1477); break; + + case '*': dtfm_tone(outpin, 941, 1209); break; + case '0': dtfm_tone(outpin, 941, 1336); break; + case '#': dtfm_tone(outpin, 941, 1477); break; + + default: return 0; + } + return 1; +} + +void dtfm_dial(char outpin, char *keys) { + for(char i=0;keys[i]!=0;i++) { dtfm_key(outpin, keys[i]); delay(100); } +} + +void setup() // run once, when the sketch starts +{ + pinMode(dtfmpin, OUTPUT); // sets the digital pin as output + //dtfm_dial(dtfmpin, "739136794"); + dtfm_tone(dtfmpin, 1, 10); +} + +void loop() // run over and over again +{ +delay(10000); +} diff --git a/arduino/led_touch/led_touch.pde b/arduino/led_touch/led_touch.pde new file mode 100644 index 0000000..498a37a --- /dev/null +++ b/arduino/led_touch/led_touch.pde @@ -0,0 +1,51 @@ +//TOUCH SENSING BETA - LED TURNS ON WHEN LIGHT IS PRESENT +//BY: RICARDO DE LEMOS 1/17/2007 +int led1 = 13; +int cath = 2; // negative +int ando = 3; // positive + +void setup() + { + pinMode(led1, OUTPUT); + pinMode(cath, OUTPUT); + pinMode(ando, OUTPUT); + //Serial.begin(9600); + } + +int dela = 20; +int last = HIGH; +int shine = HIGH; + +void loop() + { + //TURN SENSOR LED ON + pinMode(ando, OUTPUT); + if(shine) { + digitalWrite(cath, LOW); + digitalWrite(ando, HIGH); + delay(100); + } + + //REVERSE BIAS + CHARGE LED + digitalWrite(cath, HIGH); + digitalWrite(ando, LOW); + //delay(dela); + + //READ LED CAP + pinMode(ando, INPUT); + delay(dela); + int state = digitalRead(ando); + + //SWITCH + if((state != last) && state == LOW) shine = !shine; + last = state; + + //DEBUG LED + if(state) { + digitalWrite(led1,HIGH); + } else { + digitalWrite(led1,LOW); + } + } + + diff --git a/arduino/oscilator/oscilator.pde b/arduino/oscilator/oscilator.pde new file mode 100644 index 0000000..3c45854 --- /dev/null +++ b/arduino/oscilator/oscilator.pde @@ -0,0 +1,36 @@ +/* Pong controller (for use with hPong) + * <~~Harvie 2oo8 + */ + +#define inpin 0 +int min = 65535, max = 0; +int stadium_max = 70; +char offset = 0; +float val = 0, oldval = -255; +int sndPin = 12; + +void setup() // run once, when the sketch starts +{ + stadium_max+=offset; + Serial.begin(19200); + pinMode(sndPin, OUTPUT); +} + +void loop() // run over and over again +{ + val = analogRead(inpin); + if(valmax) max=val; + val=(((val-(min))/(max-(min)))*stadium_max)-offset; + /*if(val!=oldval) { + oldval = val; + //Serial.print(min, DEC); Serial.print("-"); Serial.print(max, DEC); Serial.print("\n"); + //Serial.print(val, DEC); Serial.print("\n"); + //Serial.print(val, BYTE); + }*/ + val=val; + digitalWrite(sndPin, HIGH); + delay(val); + digitalWrite(sndPin, LOW); + delay(val); +} diff --git a/arduino/serial_midi/serial_midi.pde b/arduino/serial_midi/serial_midi.pde new file mode 100644 index 0000000..4ecfcf4 --- /dev/null +++ b/arduino/serial_midi/serial_midi.pde @@ -0,0 +1,71 @@ +// ***************************************************************************************************************** +// * * +// * SpikenzieLabs.com * +// * * +// * Very Simple Serial to MIDI DEMO * +// * * +// ***************************************************************************************************************** +// +// BY: MARK DEMERS +// May 2009 +// VERSION: 0.1 +// +// DESCRIPTION: +// Demo sketch to play notes from middle C in the 4th octave up to B in the 5th octave and then back down. +// +// +// HOOK-UP: +// 1. Plug USB cable from Arduino into your computer. +// +// +// USAGE: +// 1. Install and Set-up Serial MIDI Converter from SpikenzieLabs +// 2. Open, compile, and upload this sketch into your Arduino. +// 3. Run Serial MIDI Converter in the background. +// 4. Launch your music software such as Garage Band or Ableton Live, choose a software instrument and listen to the music. +// +// +// LEGAL: +// This code is provided as is. No guaranties or warranties are given in any form. It is up to you to determine +// this codes suitability for your application. +// + +int note = 0; + +void setup() +{ + Serial.begin(57600); // Default speed of the Serial to MIDI Converter serial port +} + +void loop() +{ + + for(int note=60; note<=83; note++) // Going Up + { + MIDI_TX(144,note,127); // NOTE ON + delay(100); + + MIDI_TX(128,note,127); // NOTE OFF + delay(100); + } + + for(int note=82; note>=61; note--) // Coming Down + { + MIDI_TX(144,note,127); // NOTE ON + delay(250); + + MIDI_TX(128,note,127); // NOTE OFF + delay(250); + } + +} + + +void MIDI_TX(unsigned char MESSAGE, unsigned char PITCH, unsigned char VELOCITY) +{ + Serial.print(MESSAGE); + Serial.print(PITCH); + Serial.print(VELOCITY); +} + + diff --git a/arduino/tv_b_gone_Pedrocrespo/tv_b_gone_Pedrocrespo.pde b/arduino/tv_b_gone_Pedrocrespo/tv_b_gone_Pedrocrespo.pde new file mode 100644 index 0000000..0deb1b7 --- /dev/null +++ b/arduino/tv_b_gone_Pedrocrespo/tv_b_gone_Pedrocrespo.pde @@ -0,0 +1,309 @@ +/* Arduino TV-B-Gone +* +* A recreation of the TV-B-Gone kit on an Arduino Duemilanove. +* By Daedalus12, mtbf0, westfw and Pedrocrespo +* +*/ + +#include + +struct codeElement { + uint32_t onTime; // duration of "On" time + uint32_t offTime; // duration of "Off" time +}; + +struct powercode { + uint32_t freq; // frequency + struct codeElement codes[100]; // on/off codes, supposed to be 100 as maximum +}; + + int i = 0; // we use this for iterating + long cfreq; // we'll store each frequency here when needed + +const struct powercode sonyCode PROGMEM = { + 37470, + {{245, 60}, + {123, 60}, + {61 , 60}, + {123, 60}, + {61 , 60}, + {123, 60}, + {61 , 60}, + {61 , 60}, + {123, 60}, + {61 , 60}, + {61 , 60}, + {61 , 60}, + {61 , 2759}, + {245, 60}, + {123, 60}, + {61 , 60}, + {123, 60}, + {61 , 60}, + {123, 60}, + {61 , 60}, + {61 , 60}, + {123, 60}, + {61 , 60}, + {61 , 60}, + {61 , 60}, + {61 , 0}} +}; +const struct powercode panasonicCode PROGMEM = { + 36130, + {{358,179}, + {44, 45}, + {44, 135}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 135}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 135}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 135}, + {44, 45}, + {44, 135}, + {44, 135}, + {44, 135}, + {44, 135}, + {44, 45}, + {44, 45}, + {44, 135}, + {44, 45}, + {44, 135}, + {44, 135}, + {44, 135}, + {44, 135}, + {44, 45}, + {44, 135}, + {44, 7720}, + {358, 180}, + {44, 45}, + {44, 135}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 135}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 135}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 45}, + {44, 135}, + {44, 45}, + {44, 135}, + {44, 135}, + {44 ,135}, + {44 ,135}, + {44, 45}, + {44, 45}, + {44, 135}, + {44, 45}, + {44, 135}, + {44, 135}, + {44, 135}, + {44, 135}, + {44, 45}, + {44, 135}, + {44, 0}} +}; + +const struct powercode sony2Code PROGMEM = { + + 37470, + + { {245, 60}, + + {123, 60}, + + {123, 60}, + + {123, 60}, + + {123, 60}, + + {61, 60}, + + {123, 60}, + + {61, 60}, + + {123, 60}, + + {61, 60}, + + {61, 60}, + + {61, 60}, + + {61, 2636}, + + {246, 60}, + + {123, 60}, + + {123, 60}, + + {123, 60}, + + {123, 60}, + + {61, 60}, + + {123, 60}, + + {61, 60}, + + {123, 60}, + + {61, 60}, + + {61, 60}, + + {61, 60}, + + {61, 0} } + +}; + + + +const struct powercode sony3Code PROGMEM = { + + 74940, + + { {250, 63}, + + {121, 63}, + + { 60, 63}, + + {121, 63}, + + { 60, 63}, + + {121, 63}, + + { 60, 63}, + + { 60, 63}, + + {121, 63}, + + { 60, 63}, + + { 60, 63}, + + { 60, 63}, + + { 60, 2819}, + + {250, 63}, + + {121, 63}, + + { 60, 63}, + + {121, 63}, + + { 60, 63}, + + {121, 63}, + + { 60, 63}, + + { 60, 63}, + + {121, 63}, + + { 60, 63}, + + { 60, 63}, + + { 60, 63}, + + { 60, 0} + + } + +}; +PROGMEM const powercode *powerCodes[] = { + &sonyCode, &panasonicCode, &sony2Code, &sony3Code +}; // select the codes you like + +int num_codes = (sizeof(powerCodes)/sizeof(*powerCodes)); // count how many codes are in the list + +void setup() { + DDRD = _BV(DDD6); // sets Pin 6 as output +} + +void loop(){ + for(i=0;i